ProSoft Technology ProLinx-HART Specifications Page 23
- Page / 119
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Functional Overview HART ♦ ProLinx Gateway
Driver Manual HART Master
ProSoft Technology, Inc. Page 23 of 119
July 7, 2009
2.3.3 HART Command List
The HART Command List specifies the commands to be executed to the HART
devices connected to a channel. A HART command can be seen as an outgoing
message to the HART devices that provides Write Data for a specific command
or a response message that carries process data (Read Data) back to the
module. The ProLinx module supports three kinds of data blocks in the Universal
and Common Practice commands. These data blocks are:
Integers
IEEE 754 Floating Point Numbers (32 bits)
Packed ASCII character strings
The Packed ASCII character strings are unpacked and placed with the integers
data block.
For all commands, it is possible to select where the Write Data comes from; it
can be in the module’s internal database or it can be configured as a fixed data
block in the command.
For response messages from HART devices, it is possible to configure where the
Floating Point Data and Integer Data will be placed in the module’s internal
database, but this is only possible for the Universal and Common Practice
commands. In the case of Device Specific commands, all the Read Data is
placed in the Integer data section. See HART Command Support for a listing of
supported HART commands.
- DRIVER MANUAL 1
- All ProLinx® Products 2
- Your Feedback Please 3
- Contents 5
- 1 Start Here 7
- 1.2 Package Contents 8
- 1.5.1 Using the Help System 10
- 2 Functional Overview 11
- Port Label Function 12
- Channel 6 Hart Port 5 12
- Channel 7 Hart Port 6 12
- Channel 8 HART Port 7 12
- 2.3.2 Auto-Polling 15
- 2.3.3 HART Command List 23
- 3 Configure the Gateway 25
- EFAULT PROJECT and 26
- 3.1 Module Entries 27
- 3.3 [HART PORT x] 28
- 3.3.1 Enabled 28
- 3.3.2 Preambles 29
- 3.3.3 Primary Master 29
- 3.3.4 Retry Count 29
- 3.3.5 DB Address Status 29
- 3.3.6 Command Count 29
- 3.3.7 Auto-Poll Code 30
- 3.3.8 Auto-Poll DB Address 30
- 3.3.9 Auto-Poll Swap Float 30
- 3.3.10 Max Device Count 30
- 3.4 [HART PORT x COMMANDS] 31
- 3.4.1 Command List Overview 31
- 3.4.3 Enable 32
- 3.4.4 Float DB Address 33
- 3.4.5 Poll Interval 33
- 3.4.6 FP Word Count 33
- 3.4.7 Swap Code 33
- 3.4.8 Short Address 34
- 3.4.9 Function Code 34
- 3.4.10 Int. DB Address 36
- 3.4.11 Int Word Count 36
- 3.4.12 Swap Code 37
- 3.4.13 Use Long 37
- 3.4.14 Enable DB Address 37
- 3.4.15 Done DB Address 37
- 3.4.16 Write DB Address 37
- 3.4.17 Swap Code 38
- 3.4.18 Byte Count 38
- 3.4.19 Fixed Data 38
- 3.5 Data Map 39
- 3.5.2 From Address 40
- 3.5.3 To Address 40
- 3.5.4 Register Count 40
- 3.5.5 Swap Code 40
- 3.5.6 Delay Preset 41
- OWNLOAD dialog box opens 42
- OWNLOAD button 42
- 4 Error/Status Data 43
- 4.6.2 Slave List Status 47
- 4.7 Module Error Codes 47
- 4.7.1 Protocol Error Codes 47
- 5 Reference 51
- Word High Byte Low Byte 55
- 0 STATUS WORD 55
- 1 Polling Address 0 55
- COMMAND 12 - Read Message 56
- COMMAND 17 - Write Message 61
- COMMAND 39 - EEPROM Control 70
- COMMAND 43 - Set PV Zero 74
- COMMAND 44 - Write PV Units 75
- COMMAND 45 - Trim DAC Zero 76
- COMMAND 46 - Trim DAC Gain 77
- 1 Transfer Function Code 0 78
- Type Network Power Supply 94
- A Required 94
- B Required 94
- C Must not be used 94
- 5.4 HART Status Data Map 102
- 5.4.2 Port 0 Command Errors 102
- 5.4.4 Port 1 Command Errors 103
- 5.4.5 Port 2 Data 103
- 5.4.9 Port 6 Data 104
- 5.4.10 Port 7 Data 104
- 5.4.6 Port 3 Data 104
- 5.4.7 Port 4 Data 104
- 5.4.8 Port 5 Data 104
- 5.5 Module Status Values 105
- 5.5.1 Normal Operation 105
- 5.5.2 Interface Crash Codes 105
- 5.5.3 Fatal Crash Codes 105
- 5.5.4 Peer Status Codes 106
- 5.6 Module Status Data Map 107
- 5.6.2 HTTP Port 80 Status 107
- 5.6.3 SNTP Client Status 107
- In This Chapter 111
- 6.2.1 All Product Returns: 112
- 6.3 LIMITED WARRANTY 113
- 6.3.8 No Other Warranties 116
- 6.3.9 Allocation of Risks 116
- Write DB Address • 37 119
- Your Feedback Please • 3 119
Related products and manuals for Gateways/controllers ProSoft Technology ProLinx-HART
(86 pages)© 2020, manymanuals.com. All rights reserved. | 0.852 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals