ProSoft Technology ProLinx-HART Specifications Page 34
- Page / 119
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
HART ♦ ProLinx Gateway Configure the Gateway
HART Master Driver Manual
Page 34 of 119 ProSoft Technology, Inc.
July 7, 2009
Swap Code Description
0 None - No Change is made in the byte ordering (1234 = 1234)
1 Words - The words are swapped (1234=3412)
2
Words & Bytes - The words are swapped then the bytes in each word are
swapped (1234=4321)
3 Bytes - The bytes in each word are swapped (1234=2143)
3.4.8 Short Address
1 to 15
This parameter specifies the HART slave node address on the network to be
considered. Values of 1 to 15 are permitted. If the device to be addressed only
accepts long address, then the parameter "Use Long" should be selected so the
module can ask for the long address with the short one and then execute the
command.
3.4.9 Function Code
0 to 255
This parameter specifies the HART function to be executed. Any HART function
can be executed, even device specific ones, but only supported commands will
return formatted data and classified in floating point data and integer data.
Commands Supported by the Module
The format of each command in the list is independent on the function being
executed. All parameters in the command table must be entered. Only one
parameter is optional, the Fixed Data field, which contains data to be sent to a
HART device. The tables below list the functions supported by the module:
HART Universal Commands Set
Command Definition
00 Read Unique Identifier
01 Read Primary Variable
02 Read Current And Percent Of Range
03 Read Dynamic Variables
06 Write Polling Address
07 Read Loop Configuration
08 Read Dynamic Variable Classifications
09 Read Device Variables with Status
11 Read Unique Identifier Associated With Tag
12 Read Message
13 Read Tag Descriptor Date
14 Read PV Sensor Info
15 Read Output Information
- DRIVER MANUAL 1
- All ProLinx® Products 2
- Your Feedback Please 3
- Contents 5
- 1 Start Here 7
- 1.2 Package Contents 8
- 1.5.1 Using the Help System 10
- 2 Functional Overview 11
- Port Label Function 12
- Channel 6 Hart Port 5 12
- Channel 7 Hart Port 6 12
- Channel 8 HART Port 7 12
- 2.3.2 Auto-Polling 15
- 2.3.3 HART Command List 23
- 3 Configure the Gateway 25
- EFAULT PROJECT and 26
- 3.1 Module Entries 27
- 3.3 [HART PORT x] 28
- 3.3.1 Enabled 28
- 3.3.2 Preambles 29
- 3.3.3 Primary Master 29
- 3.3.4 Retry Count 29
- 3.3.5 DB Address Status 29
- 3.3.6 Command Count 29
- 3.3.7 Auto-Poll Code 30
- 3.3.8 Auto-Poll DB Address 30
- 3.3.9 Auto-Poll Swap Float 30
- 3.3.10 Max Device Count 30
- 3.4 [HART PORT x COMMANDS] 31
- 3.4.1 Command List Overview 31
- 3.4.3 Enable 32
- 3.4.4 Float DB Address 33
- 3.4.5 Poll Interval 33
- 3.4.6 FP Word Count 33
- 3.4.7 Swap Code 33
- 3.4.8 Short Address 34
- 3.4.9 Function Code 34
- 3.4.10 Int. DB Address 36
- 3.4.11 Int Word Count 36
- 3.4.12 Swap Code 37
- 3.4.13 Use Long 37
- 3.4.14 Enable DB Address 37
- 3.4.15 Done DB Address 37
- 3.4.16 Write DB Address 37
- 3.4.17 Swap Code 38
- 3.4.18 Byte Count 38
- 3.4.19 Fixed Data 38
- 3.5 Data Map 39
- 3.5.2 From Address 40
- 3.5.3 To Address 40
- 3.5.4 Register Count 40
- 3.5.5 Swap Code 40
- 3.5.6 Delay Preset 41
- OWNLOAD dialog box opens 42
- OWNLOAD button 42
- 4 Error/Status Data 43
- 4.6.2 Slave List Status 47
- 4.7 Module Error Codes 47
- 4.7.1 Protocol Error Codes 47
- 5 Reference 51
- Word High Byte Low Byte 55
- 0 STATUS WORD 55
- 1 Polling Address 0 55
- COMMAND 12 - Read Message 56
- COMMAND 17 - Write Message 61
- COMMAND 39 - EEPROM Control 70
- COMMAND 43 - Set PV Zero 74
- COMMAND 44 - Write PV Units 75
- COMMAND 45 - Trim DAC Zero 76
- COMMAND 46 - Trim DAC Gain 77
- 1 Transfer Function Code 0 78
- Type Network Power Supply 94
- A Required 94
- B Required 94
- C Must not be used 94
- 5.4 HART Status Data Map 102
- 5.4.2 Port 0 Command Errors 102
- 5.4.4 Port 1 Command Errors 103
- 5.4.5 Port 2 Data 103
- 5.4.9 Port 6 Data 104
- 5.4.10 Port 7 Data 104
- 5.4.6 Port 3 Data 104
- 5.4.7 Port 4 Data 104
- 5.4.8 Port 5 Data 104
- 5.5 Module Status Values 105
- 5.5.1 Normal Operation 105
- 5.5.2 Interface Crash Codes 105
- 5.5.3 Fatal Crash Codes 105
- 5.5.4 Peer Status Codes 106
- 5.6 Module Status Data Map 107
- 5.6.2 HTTP Port 80 Status 107
- 5.6.3 SNTP Client Status 107
- In This Chapter 111
- 6.2.1 All Product Returns: 112
- 6.3 LIMITED WARRANTY 113
- 6.3.8 No Other Warranties 116
- 6.3.9 Allocation of Risks 116
- Write DB Address • 37 119
- Your Feedback Please • 3 119
Related products and manuals for Gateways/controllers ProSoft Technology ProLinx-HART
(86 pages)© 2020, manymanuals.com. All rights reserved. | 0.772 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals