ProSoft Technology ProLinx-HART Specifications Page 30
- Page / 119
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
HART ♦ ProLinx Gateway Configure the Gateway
HART Master Driver Manual
Page 30 of 119 ProSoft Technology, Inc.
July 7, 2009
3.3.7 Auto-Poll Code
P, M or N
This parameter sets the auto-poll mode of the channel. If the parameter is set to
P, the module will automatically poll device 0 in point-to-point mode. If the
parameter is set to M, the module will automatically poll devices 1 to n (n=value
of parameter Max Device Count). If the parameter is set to N, the auto-polling
option will be disabled and only commands in the command list will be utilized for
the channel. In the auto-poll mode, the module will automatically execute HART
commands 0, 3, 13, 14 and 15.
3.3.8 Auto-Poll DB Address
0 to 3700
This parameter sets the starting address for the data obtained by the auto-poll
feature. Each device on a channel requires 50 words in the database. The data
area selected must not overlap any portion of the database used by other
channels or the module.
3.3.9 Auto-Poll Swap Float
0 to 3
This parameter swaps the floating-point data values received by the auto-poll
feature.
Swap Code Description
0 None - No Change is made in the byte ordering (1234 = 1234)
1 Words - The words are swapped (1234=3412)
2
Words & Bytes - The words are swapped then the bytes in each word are
swapped (1234=4321)
3 Bytes - The bytes in each word are swapped (1234=2143)
Depending on the host processor using the data, the proper swap code must be
utilized to present the data in the correct format.
3.3.10 Max Device Count
1 to 15
This parameter sets the maximum number of slave devices to be utilized for the
auto-poll feature. In point-to-point mode, the parameter should be set to a value
of 1. In multi-drop mode, the parameter should be set from 1 to 15 to represent
the number of slave devices attached to the channel.
- DRIVER MANUAL 1
- All ProLinx® Products 2
- Your Feedback Please 3
- Contents 5
- 1 Start Here 7
- 1.2 Package Contents 8
- 1.5.1 Using the Help System 10
- 2 Functional Overview 11
- Port Label Function 12
- Channel 6 Hart Port 5 12
- Channel 7 Hart Port 6 12
- Channel 8 HART Port 7 12
- 2.3.2 Auto-Polling 15
- 2.3.3 HART Command List 23
- 3 Configure the Gateway 25
- EFAULT PROJECT and 26
- 3.1 Module Entries 27
- 3.3 [HART PORT x] 28
- 3.3.1 Enabled 28
- 3.3.2 Preambles 29
- 3.3.3 Primary Master 29
- 3.3.4 Retry Count 29
- 3.3.5 DB Address Status 29
- 3.3.6 Command Count 29
- 3.3.7 Auto-Poll Code 30
- 3.3.8 Auto-Poll DB Address 30
- 3.3.9 Auto-Poll Swap Float 30
- 3.3.10 Max Device Count 30
- 3.4 [HART PORT x COMMANDS] 31
- 3.4.1 Command List Overview 31
- 3.4.3 Enable 32
- 3.4.4 Float DB Address 33
- 3.4.5 Poll Interval 33
- 3.4.6 FP Word Count 33
- 3.4.7 Swap Code 33
- 3.4.8 Short Address 34
- 3.4.9 Function Code 34
- 3.4.10 Int. DB Address 36
- 3.4.11 Int Word Count 36
- 3.4.12 Swap Code 37
- 3.4.13 Use Long 37
- 3.4.14 Enable DB Address 37
- 3.4.15 Done DB Address 37
- 3.4.16 Write DB Address 37
- 3.4.17 Swap Code 38
- 3.4.18 Byte Count 38
- 3.4.19 Fixed Data 38
- 3.5 Data Map 39
- 3.5.2 From Address 40
- 3.5.3 To Address 40
- 3.5.4 Register Count 40
- 3.5.5 Swap Code 40
- 3.5.6 Delay Preset 41
- OWNLOAD dialog box opens 42
- OWNLOAD button 42
- 4 Error/Status Data 43
- 4.6.2 Slave List Status 47
- 4.7 Module Error Codes 47
- 4.7.1 Protocol Error Codes 47
- 5 Reference 51
- Word High Byte Low Byte 55
- 0 STATUS WORD 55
- 1 Polling Address 0 55
- COMMAND 12 - Read Message 56
- COMMAND 17 - Write Message 61
- COMMAND 39 - EEPROM Control 70
- COMMAND 43 - Set PV Zero 74
- COMMAND 44 - Write PV Units 75
- COMMAND 45 - Trim DAC Zero 76
- COMMAND 46 - Trim DAC Gain 77
- 1 Transfer Function Code 0 78
- Type Network Power Supply 94
- A Required 94
- B Required 94
- C Must not be used 94
- 5.4 HART Status Data Map 102
- 5.4.2 Port 0 Command Errors 102
- 5.4.4 Port 1 Command Errors 103
- 5.4.5 Port 2 Data 103
- 5.4.9 Port 6 Data 104
- 5.4.10 Port 7 Data 104
- 5.4.6 Port 3 Data 104
- 5.4.7 Port 4 Data 104
- 5.4.8 Port 5 Data 104
- 5.5 Module Status Values 105
- 5.5.1 Normal Operation 105
- 5.5.2 Interface Crash Codes 105
- 5.5.3 Fatal Crash Codes 105
- 5.5.4 Peer Status Codes 106
- 5.6 Module Status Data Map 107
- 5.6.2 HTTP Port 80 Status 107
- 5.6.3 SNTP Client Status 107
- In This Chapter 111
- 6.2.1 All Product Returns: 112
- 6.3 LIMITED WARRANTY 113
- 6.3.8 No Other Warranties 116
- 6.3.9 Allocation of Risks 116
- Write DB Address • 37 119
- Your Feedback Please • 3 119
Related products and manuals for Gateways/controllers ProSoft Technology ProLinx-HART
(86 pages)© 2020, manymanuals.com. All rights reserved. | 1.396 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals